Bagersko hidravlično kladivo dleto
Opis izdelkov
1.Material:40Cr ali 42CrMo
2.Dimenzija:Odvisno od specifikacije orodja Tool Maker
3.Vrsta dleta:Moil Point, Blunt Tool, Flat, wedge
4.Toplotna obdelava:
Temperatura avstencije 810~850 (20min/palec)
Hlajenje Vodno hlajenje z oljem
Kaljenje 250~300 (1h/inch)
5.Mehanske lastnosti:
Površinska trdota HRC51±3
Trdota jedra HRC35± 3
Natezna trdnost (min) 1250N/mm²
Meja tečenja (min.) 950N/mm²
Raztezek 10~14%
Zmanjšanje površine 35~40%
Udarno delo 23~28 ft1b
Velikost zrn 7,0~8,0
Pakiranje in pošiljanje
Oblikovanje in struktura
Za naslednje predmete imamo hidravlično kladivo
| Krupp | HM45, HM50/60, HM60/75, HM85, HM130/135, HM170/185, HM200, HM300/301, |
| HM400/401, HM550, HM560CS, HM580, HM600/601, HM700 | |
| NABIJAČ | S21,S20/22,ROX100,S23,S25,S26/,ROX400,S29,S52/,ROX700, |
| S54/700, S55, S56/800, S82/1400 | |
| NPK | H1XA, H2XA, H3XA, H4X, H6XA, H7X, H8XA, H10XA |
| INDECO | MES350,HB5,MES553,MES621,MES1200,HB12,HB19,MES1800,HB27,MES2500 |
| MONTABERT | BRH30,BRH40,BRH45,BRH60,BRH76/91,BRP100,BRP130,BRP125,BRH250, |
| RH501,BRH620, BRH625,BRH750,BRV32 | |
| STANLEY | MB125,MB250/350,MB550,MB656,MB800,MB1550, |
| MB1950/1975,MB30EX,MB40EX | |
| FURUKAWA | HB05R, HB1G, HB2G, HB3G, HB5G, HB8G, HB10G, HB15G, HB20G |
| HB30G, HB40G, HB50G, | |
| TOKU/TOYO | TNB1E,TNB2E,TNB4E,TNB6E,TNB7E,TNB14E,TNB22EA,THBB101, |
| OKADA | OUB301,OUB302,OUB303,OUB305,OUB308,OUB310,OUB312,OUB316,OUB318, |
| SOOSAN | SB10, SB20, SB30, SB35, SB40, SB43, SB45, SB50, SB60, SB70, SB81, |
| SB100, SB121, SB130, SB151 | |
| KWANGLIM | SG200,SG300,KSG350,SG400,SG600,SG800,SG1200,SG1800,SG2100,SG2500, |
| DAEMO | DMB03,DMB04,DMB06,S150-V,S300-V,S500-V,S700-V,S900-V,S1300-V,S1800-V |
| HANWOO | RHB301, RHB302, RHB303, RHB304, RHB305, RHB306, RHB308, RHB309, RHB313, |
| DAINONG | D30,D50,D60,D70/90,D110,D130,D160,T180,K20 |
| K25,K30,K50,K80,K120,K55S,K40S, |
Material
